Miniature painting

Author Archive

How to paint Moria Goblins

After I painted my first set of 24 goblins I had planned to post a tutorial on how I painted them.  I never really got around to it until now.  I haven’t done anything special, all the colours and the theme align closely with how Games Workshop paints theirs. I have been noticing that my blog gets a number of hits for “How to paint Moria Goblins,”  So clearly people are still looking for a walkthrough, and hopefully this will be useful to you.  There are a lot of pictures, I took a photo of every single stage, so this will be really pic heavy.  If you feel I skipped over anything or just have questions feel free to drop them in the comments below.

With these goblins I decided to base them before I put the primer on, this is so I can dry brush them first, as when I do it last I always mess up the mini, and I really want to avoid that.  So the first photo here has the mini primed and the base hase been drybrushed, but not cleaned up yet.  In the second shot I have cleaned the mini up with black paint, ready to go.  I next painted the eyes, a mixture of white and yellow, no exact ratio as I change it when I bulk paint so that only a few have the same eye colour.  I have painted the eyes now as I wouldn’t be able to get into the helmet later without messing everything up.

In the next shot I clean up all the excess around the eyes, this again is much easier to do now, and then paint a straight line down the eye for the pupil.  I use my 000 brush for this part, it takes some patience, but if I mess it up I can always paint over it and try again.  Next I did the base coat of the green using Games Workshop Gretchin Green foundation paint.  This is a bit early as I would normally do any dry brushing before painting anything else, but again that helmet would give me too much trouble.  I am not too worried about getting a good coat on the skin as I will touch this up after the dry brushing, I then cleaned up any over paint with black.

Now we start with the dry brushing, I first put down a coat of Tin Bitz, then Boltgun metal.  At the same time I paint the chainmail Boltgun.  I don’t worry too much about getting paint on the goblins skin as I will touch that up before too long.  I over did the Boltgun Metal, drowning out the Tin Bitz, while I will be able to tone down the Boltgun with washes there isn’t much I can do for the Tin.  In the last of the three shots I paint all the leather straps, the bow, and the quiver all Bestial Brown.  I will differentiate the wood of the bow from the leather with different highlights later.

Moving on, I paint the clothes that stick out from under the armour Scab Red, I also paint the part around his neck.  I am not sure what that is, but painting it red gives this guy a little more of a punch.  The next step I paint the fletching on the arrows Codex Grey, and the shaft black, as well as repaint his gloves black.  I then repainted all the flesh with the same foundation Gretchin Green, skipping the face.  In the third photo I have applied a wash all over, trying to avoid the eyes.  I washed his armour twice to try and correct the Boltgun metal.

The first shot of these three is just the wash step again, but showing him from the back.  The wash I use has semi-gloss paint medium in it, this accounts for the now shiny goblin.   Next I work on highlighting the flesh, I start with a little of the base colour to which I have added a touch of Bleached Bone. I also add a drop or two of Matte Medium, this while make the paint slightly translucent, which helps to blend the layers together.  This highlight covers all but the darkest recesses and shadows.  The next highlight is the same mix I just used with more Bleached Bone and Matte Medium.  This time I am just picking out the tops of his ears, and some of his muscles on his arms.

I continue with another highlight again with more Bleached Bone and Matte Medium, adding water as necessary to keep the paint thin.   The very last highlight is almost straight Bleached Bone, and I only place a dot on the top of each ear and a tiny line on his arm to try to create some definition.  I now move to highlighting the leather, I am again using the base of Scorched Brown mixed with Bleached Bone and Matte Medium.  On the straps on his legs this will be the only highlight, where as the quiver will get one more.  With the straps I am trying to paint just the edges of each one.  I had too much paint on my brush and put down lines that were heavier that I had planned but that is why I started on his legs, I will be more careful when it comes to the strap across his chest.

The first photo below is a shot of the leather straps from the front.  The next step is the wood of the bow, again starting with Scorched Brown I then add Bestial Brown and the always present Matte Medium.  Again I am trying to avoid the darker areas.  The next highlight adds Snakebite Leather and Matte Medium.  I only have one shot of both those steps, the one in the middle, but I doubt there would have been much of a constrast.  The third photo is starting the red, this is the part that really makes these guys jump out at you.  The first step is to bring back the original red with Scab red, again I leave the darkest parts untouched.

The next highlight adds Red Gore and Matte Medium.  I then add Blood Red to the next highlight.  For the last highlight I add a touch of Orange, I used an artist acrylic orange I had from another project. The orange works better than white or pink as I find those, not surprisingly, are too pink. This highlight goes just on the tips and very edges. At this stage I also did the fletching on the arrows, using Codex Grey as a base and then working up using Fortress Grey, which was applied using angled dabs to replicate the look of feathers.

Alright, we are into the home strech now. I use somewhat watered down Codex Grey and paint the some of the edges of his armour. This is to simluate where his armour has taken a hit or been bashed against something and the tarnish has been removed. I suggest starting out sparingly as you can always add some more later. Codex Grey was also used to highlight just a few parts of his hair, a little bit of Fortress Grey was then added to do one more highlight. I then used Codex Grey, with a little more water, to highlight his gloves. The edge of the base then gets a touch up with Codex Grey as well.

Now all that is left is to clear coat and protect our little friend. I give him two thin coats of Krylon Crystal Clear Acrylic, notice how dark this makes him look. After that has dried I give one coat of Testors Dullcote, and you will notice in the very last shot I wasn’t patient enough and tried to pick him up before the final coat dried and left a big finger print on the base. Always feels good to screw up the final stage of a pretty solid paint job.

So there you have it, a step-by-step painting of a Games Workshop Moria Goblin. To be honest, taking a photo after each step was probably too much, I sometimes had to stare at the image to remember what I did in each step, but I took the photos so might as well use them. Let me know if you have any questions.

Painting the ONESS Fleet continued

So the next steps were fairly straight-forward, I now needed to paint all the extra panels red.  It was fairly easy to identify which panels to do, as they stood out from the rest of the larger panels.  For these I used Golden Acrylics, for the basecoat I used C.P. Cadmium Dark Red.  I have recently been using quite a number of different products from the local art store, the store is much closer than my nearest GW store, and the prices are unbeatable when compared to GW paints.  I will put a post at some point about the different products I am playing around with.  So for this fleet it is just the red paints.


So, back to the ships.  The difficult part, well actually more time consuming than anything, was getting the sides of each panel.  The panels probably average about a millimeter thick, so the sides of each are not too easy to paint.  However, it makes a real difference when you look at the ships up close.  The photo below is a good example of what I am talking about.  I also found that when I was painting the top of the panels I would go over the edge a little anyway, and then they looked quite messy and inconsistent.  So this one really was just patience, the trick was to get your brush onto the top of panel and then just roll it down the side at the same time as drawing the brush along the side.  In this manner you are painting with the side of the brush not the tip.  You will notice that I wasn’t perfect, not an issues as the small mistakes will be covered with the wash, and the bigger ones can be fixed with the original paint.


So after many hours of using very small brushes and almost going blind…  I also did all the windows at the same time, in the same manner, but using black.


Next was the wash, very diluted black paint with some acrylic medium, and a drop of future floor polish.  Here are before and after photos.  To be honest I wish I had made the wash darker, I think these ships, espeically the smaller ones would have benefited from more of a contrast.


Next came the highlighting.  This stage took forever, I highlighted each panel twice! The first highlight was the base colour lightened a little, so for the dark grey I added a little of the light grey, and the second highlight had more of the lighter colour.  I also used a good amount of acrylic medium, this starts to make the paint a little translucent, which can help with getting everything to work together.  When I first started I had a hell of a time painting with the Tamiya paints, they were totally different from anything I had used before.  Even though they are acrylic, they are solvent/thinner based, and the thinner evaporated so fast some times the paint on the end of the brush would dry before I even got it to the model.  Adding water and additional thinner would just make the pigments clump and make a big mess.  The eventual solution was the arcylic matte medium, which is basically arcylic paint without pigment.  I would add quite a bit of it to just a few drops of the Tamiya paint, and add a drop of water or two to make it flow better.  The end result was much closer to the types of paint I usually use, Citadel or Vallejo.

So here is one of the ships just prior to the highlighting


And after the first highlighting, so the next layer would be brighter and the lines would be thinner.  By making the second highlight thinner it give the effect of a bit of a fade at the edges of the panels.  The same process was used for all the red panels, with the final highlight using a little bit of orange, to avoid it looking pink.


Once all the highlighting was done, I gave all the ships a gloss coat to seal them and prep them for the decals.  I bought a whole bunch of different scale decals, 1/72, 1/144, and 1/285, as I didn’t know how they would look until I had them in my hand.  I bought most from I-94 Enterprises and Dom’s Decals.  So I applied many many decals using Micro Set and Micro Sol decal setting solutions, these are used to get the decals to look painted on.  I must say I really like the looks of the numbers, it really gives the fleet a feeling of cohesion, and makes you think there might be a lot more ships out there filling in the rest of the number series.  Nearing the end now, I did the jeweling on the windows and painted the engines.  Next they got two more thin coats of gloss coat, and then a final two thin coats of dull/matte coat.  And then they were finally finished.


Now I will just add some gratuitous close ups, they should help you see all the different highlights.  For more check out my flickr page.






Painting the ONESS Fleet

I thought I would share how I painted these ships. I borrowed the technique used to create the two tone paint job from the scale model community, and it works really well on this scale as well. To be honest when I was planning how to paint these little guys I was originally planning to try a WWI ‘Dazzle’ scheme that was used on naval vessels. However after doing some research I realized it would be too difficult and time consuming, I still think it could be pulled off but it woudl need ships that have smoother hulls. So I decided to try a two tone camo. One of the things I have started doing that I find really handy is to do a test mini, in this case I used a Battletech miniature. Doing this can help me identify anything that might be a problem, but more importantly give me a better idea of how the whole fleet will look when finished, below is the test mech.


I used Tamiya paint for these, as it works really well in my airbrush.  My airbrush doesn’t get much use on miniatures, but it is great for base coating.  If you don’t have one you can always use Tamiya spray cans, just be careful as they spray a lot of paint.  So here are the colours, quite basic just Sky Grey and Dark Grey, the white is just for the highlighting.


So the ships are first primed black using an automotive primer, I use this as it works just as well as anything else I have found and it is cheap.


Next they are basecoated in the Sky Grey, two thin coats, don’t want to cover the detail.  I start with the lighter of the two, as I want to be able to do the next coat in one go, so the dark should cover the light easier.


Then comes the neat part, using BlueTac, used for hanging posters and things, we apply a pattern.







Now you need to take care that you push the bluetack down very well, or else paint will get under and spoil the job, see below.


Don’t forget to do the bottom as well, this needs a little thought on how and where the strips will meet up.


Alright, here they are all ready to have the next colour sprayed on.


So into the spray booth, and on goes the Dark Grey.


Now we just peel off the bluetack, just use your fingers you don’t want to scratch the paint.  Don’t worry about little bits sticking, they are easily removed by neading some bluetack until it is soft and then repeatedly pressing it onto the remaining pieces and pulling it off again.  Just keep doing it and eventually it will all come off.  You can see some of it still stuck on mine below.


Alright there is step one all done, the whole fleet ready to move on.  I will cover the next steps in a follow-up post.


Finished Brigade Models ONESS fleet

Just put the finishing touches on these ships today.  This fleet has taken me a very long time to finish.  While I was going through my photos of this fleet, I found some work-in-progess photos that date back to June of 2010.  So a year and almost a half, now to be honest I put these away on the shelf a number of times.  The highlighting of every little panel just got the better of me too many times, and I would leave this project for a while and work on something else.  And of course anytime a new purchase showed up it would get all the attention, for a few days at least.  So like usual I have tonnes of photos of these guys, I will have to show some restraint in posting too many.

A big family shot to start us off.


These are all from Bridage Models, and are German or as they call it ONESS.  I can’t find any reference as to what that actually stands for. EDIT: Thanks to Aapsych20 on The Miniatures Page I now know that it stands for the Organisation of North European Sovereign States.

Now the Carrier and her Fighters.


Next the smaller ships, Destroyers and Frigates.


And then all the Capital Ships.


Not to show too much bias, but that last shot is my favorite.

Well that is a start, I have a number of posts that will follow; more detailed photos of each ship type, and some tutorials.

Hope you like them.  Feel free to add a comment.

Moria Goblins continued

The bases for these were pretty straight forward, just kitty litter as the rocks and sand for the rest of the ground.  I decided that I would paint the bases before doing the model, mainly to avoid getting paint on the finished mini.  So the whole mini was first primed black with automotive primer, and then using my airbrush I painted the bases Codex Grey, this was followed by a heavy black wash.  Then successive highlights with Codex Grey, Fortress Grey and White.  I then repainted the mini black to cover all the paint that got on them.  This process worked really well, trying to do that much dry brushing around a finished mini would have driven me crazy.


I chose four different colours for the skin.  I acutally bought about ten different colours and then using a large pad tried them all out to see which I liked best.  I chose Goblin Green and Camo Green from GW and Olive Green and Yellow Green from Vallejo, all of them were lightened with Bleached Bone for the highlights.  The reds were done with Games Workshop reds, and the last highlight got a touch of a Golden Acrylics Orange, so that it didn’t look too pink.




Moria Goblins

Just finished these within the last few days, and am now finally getting them up online.  Had a bit of a scare, after I took the photos and was uploading them to the computer I couldn’t find any of my previous photos.  Took me a while to realize that I was missing an entire harddrive.  After performing a few tests I just opened up my case, and the power lead had come a little loose.  Of course until I actually got it up and running again I was very worried that the drive had died, and I would have lost everything on it.  Lucky me it was an easy fix.

Now onto the minis.


I have had these guys sitting on a shelf for ever.  I bought the first Games Workshop box set for the Fellowship of the Ring, which included 24 goblins (I think), and over the years I picked up an additional box of 24, a number of Prowlers, Durbuz, some shamans, and some of the metal normal goblins off of eBay.  All told I have 80 goblins.  I am a fan of doing things in batches so all 80 were cleaned up, based, primed, and had the bases base-coated at once.  I also made the decision to alter them a little, as I had 48 plastic generic goblins, that repeated the same pose and weapons more often than I would like.  I only cut up a few, the vast majority got weapon swaps, almost all of the weapons came from Thunderbolt Mountain.    Between the different ranges on their site there is a really good selection of weapons.  I figured the goblins had either made a few different weapons, or most likely stole them from dead foes.




Finally finished something…

I don’t like to add posts about works in progress, as I can jump from one project to another, and thus never finish the piece in question. However that also means that if I don’t dedicate myself to getting something done this blog will sit dormant for a long time. That is just something I will need to work on as I go along. I had hoped creating this blog would help me pick up the pace on some projects, so far not the case, but maybe I will blame that on the summer. Hard to hide in the basement painting when it is nice out. We will see what the fall and winter brings. The good news is that I actually have some finished minis ready to post. I just spent what feels like the last few months painting 24 Moria Goblins from the Lord of the Rings, sold by Games Workshop. I am glad they are done, but they are less than 1/3 or my total Moria army, and that doesn’t even include the trolls or spiders. Anyway I will add a few posts over the next few days to show them off. Here is a group shot as a teaser.


Trying new techniques

I recently ordered a batch of small dice (6mm) and flying bases from EM4 Miniatures, and while I was there I decided to grab a set of their generic “Spacecraft”.  You get twelve different gray plastic ships and accompanying bases all for 2.55 pound, or $4 Canadian.  I just got them on a whim, I had heard a few people recommend them in different forums but hadn’t thought too much about them.  When they arrived, which was pretty quick considering they were coming across the Atlantic, I was thoroughly surprised.  They are great, very nice sculpts, no flash to clean up, and some fairly small mold lines to scrape off.  I had them cleaned, based, and primed in a day or two.

There are a few reasons I am excited to work on them, the first is they are generic, so I don’t feel the need to match them up to someone else’s scheme, and second is how cheap they are.  I have paired them up so I will paint each pair with the same scheme, for no real reason other than I can try each paint technique twice.  And that is why their cheapness is important, I am just going to try a whole bunch of new techniques on them, and I don’t have to worry.  No fleet that they will need to match, no expensive mini to strip the paint off if I don’t like it, just a bunch of ships I can do whatever I want with.  And I have already started…


I tried a number of new things with these two.  First was painting them just black, they turned out okay, but I had a horrible time trying to highlight them.  Second was the lightning, I had a great time doing it.  The first ship I did is the one on the right with the skinnier bolts.  I prefer the look of that one up close, but from a few feet the thicker bolts look better.  The third was the fade/blend on the cockpit glass.  I usually use the jewel technique for windows, but decided that these ships needed something a little flashier to go with the overall paint job, the picture doesn’t do the cockpits justice.  I also tried doing a different colour on the engines, usually I do a blue to white transition, but this time I tried an orange to white.  I definitely didn’t have the right shade of orange, and it didn’t turn out as I had hoped.

I had one other thing go, well not quite wrong, but not good either.  When I am done painting the miniatures I give them a couple coats of high gloss spray varnish to protect them, and then a last coat of matte varnish to finish them off.  I will admit that I am paranoid of the paint getting chipped or rubbed off, so I can over do it with the gloss varnish, and I definitely went way overboard this time.  It kind of shows in the photos, the panel lines are basically gone, I filled them with varnish, obscuring a lot of detail.  On the next pair I think I will try brushing the gloss varnish on by hand and see what I can do.  It will take a longer time, but I should be able to control the amount a lot better, the big question is whether or not I can avoid brush strokes.

And for those checking my blog out for the eye candy only, one more shot…


Step Three: Highlighting

So this post should wrap up the walk-through on this ship, only the highlighting and finishing touches left.

I highlighted the Bleached Bone first, I added a little White, and an equal amount of Matte Medium, and a little water.  The Matte Medium, is basically paint without the pigment, by adding it to the mix my paint becomes slightly translucent.  This way each highlight just blends into the previous coat a little.  I made the Bleached Bone highlight a little too bright, and ended up putting it on too much in a couple of places, so I only did the one layer of highlight.  Next was the Scorched Brown, same mix to the paint, and this time on the second highlight I added a little Bleached Bone and just did the very edges.  Next was the reds, I started with Red Gore, and then added some Blood Red for the second highlight.  I then did the metal parts, using Chainmail for most of the highlights, and then just picking out the very edges and highest points with Mithril Silver.



At this stage the painting of the ship was finished, and it went into my spraybooth for a few coats of gloss varnish.  After the first coat I noticed that I forgot to paint the engines, so I quickly painted a blue to white transition, and with the aid of the hair dryer, I had it back in the spraybooth in a few minutes.

Once the gloss coats had a good amount of time to dry, I then added two coats of matte varnish.  I am always amazed at the change adding the matte varnish makes to the paint job, up until this point the highlights were looking a little garish, but as soon as I hit it with the matte varnish everything chilled out nicely.  Below you can see the difference, the first photo is just the gloss, and the second is the matte.



The big benefit of the type of basing I do, is being able to remove the base once the ship is done and repaint it.  Through out the process I had been getting overspray and errant brush strokes all over it.  I just pop the mini off, secure a barrel clasp to the top to protect the threads, and quickly re-prime it black, and then give it a gloss coat.  For whatever reason I prefer for the mini to be matte and the base to be gloss, and that is a really easy way to accomplish it.

And one last group shot of some of my other finished Narn ships to end this walk-through.  I hope you found this at least entertaining if not informative.  Now on to my next project, which should make its way up here soon.



Step Two: Base Painting and the Wash

Painting the iconic Narn pattern on a ship can be intimidating, before I painted my first one I did a lot of research on how other people managed theirs.  It takes some patience but overall isn’t difficult, and is totally worth the effort.  The paint scheme that I picked out for my Narn ships is fairly simple, but I think works quite well. While this ship was done entirely with Games Workshop paints, I also use Vallejo, Tamiya, and have started playing around with artist’s paints from the local art store.

For this ship I used:

Scab Red
Red Gore
Blood Red
Boltgun Metal
Mithril Silver
Bleached Bone
Scorched Brown

I tend to paint my miniatures on the darker side, I almost always start with a black primer, and pick fairly dark shades as the base colour.  I like the grittier look to anything I paint, especially spaceships.  To me space is lonely, dark, and cold, and I want anything I paint to fit into that picture.

So for this ship I started with a base coat of Scab Red, applied with my airbrush.  I find that this is pretty much the only way to apply a red base coat, applying red to anything is a pain, but even more so when trying to cover a black primer.  Using a hair dryer on low to speed up drying, I applied four thin coats.


Next I start applying the geometric pattern that makes any Narn ship so unique.  I use a thined Bleached Bone for this, white would be too much of a contrast, and I need something that I can highlight later.  The actual pattern is purely freehand, with no real planning, I just sit down and start.  To help me out I surround myself with reference material, I have any previous Narn ship I have painted, and on my netbook a number of images of either shots from the tv show or miniatures that others have painted.  This way anytime I get stuck as to the next shape I should stick in I just look around.  To stop myself from being to repetative I make sure to start at a different place on eash section of the ship.


After laying down the first coat of Bleached Bone, I quickly went in with Boltgun metal and gave all the appropriate parts a coat, and then set it aside to dry.  I then applied a second coat of the Bleached Bone, the first coat is quite thin, which is necessary for me to have the control that I need to put it down correctly.  The second coat also allows me to tighten up some of the lines from the first go through.  The second coat is also fairly thin, and I don’t need to worry too much about coverage as most of it will be covered with the next step.


For the second part of the geometric pattern I use a mix of Scorched Brown and Black, probably 2:1, but really just done by eye and thinned with water.  Again straight Black would be too dark, and then the highlights would be grey based, and I prefer brown shades.  This is also applied in two thin coats.  I don’t have a photo of it, but the first coat left too much of the Bleached Bone showing, so the second coat was really necessary.  This is the coat that takes the most patience, however mistakes can be fixed quite easily with touch ups.



The next steps were a couple of washes.  I use a wash that is a mix of glaze medium, water, black ink, and a little future acrylic floor polish.  I applied this straight, to everywhere but the metalic parts, and once dry I returned with a little more into some of the darker crevasses.  For the metal, I added a drop of black ink to four of five of the normal wash, and then heavily diluted it with water, this was then liberally applied.  I would return with a dry brush to soak up any excess to avoid getting tide marks when it dried.  This was then left for a day or two to properly dry.  The glaze medium makes the entire miniature shiny, and helps to seal/protect the previous coats of paint.



Next post I will cover the highlighting and finishing steps.

Step One: Construction

After I picked this ship I had to make molds of the Thentus and the Var’Nic.  I did the Var’Nic first with no problems, with the Thentus though I did have some issues.  Before I took the mold I added some Evergreen Styrene strips to the underside in some of the really thin areas.  I was a little worried about how strong the plastic resin would be, especially as it does not have the same flexibility as white metal.  When I was making the mold I ran into a problem, the scale I was using to measure out the two part RTV solution sucked.  Bascially if you added material slowly enough it wouldn’t register, that and the smallest measurement on the scale was one gram, I made one half of the mold with too little of the catalyst.  I am sure I could re-do that half of the mold but I am waiting on a new better scale before I try.  Interestingly enough the mold works, but I get very strange flash on the model, it is almost hairy, and takes quite a bit of work to clean off.  Not really a big deal though as with this model the stars are the two Var’Nics.

So I cast the models, cleaned the flash off of them and set to work.  The first step was to sand down the Var’Nics where they would meet and get the angle I wanted, and then I drilled out a hole in each one to pin them together.  They were then superglued together.

I then cut off the two sides of the Thentus, and started filling the bubbles that are visible in some of the photos with Squadron greenstuff.  The Thentus had a large number of bubbles and flash, mainly my own fault, but it took some work to get ready.

I then sanded the Thentus so that it would meet the two Var’Nics and then superglued it in place.  The next step was to secure the barrel clasp to the bottom for the base to attach to.  I use the same basic method that Star Ranger uses over at, the only difference is I use the original post instead of replacing it.  To strengthen the post I use a drill press to drill a small hole about a quarter the way down, that I then fit a brass rod in that also inserts into the bottom of the barrel clasp.  Both ends of the clasp are held in place with epoxy putty, I use 90 second stuff I get from the local hardware store, while adding the barrel clasp to the ship I also used some left over epoxy to strengthen the connection between the Thentus and the Var’Nics.  I will probably do a tutorial on my version of Star Rangers basing method one day, just need to remember to take photos.

In the above photo you can see where I thickened the Thentus, there is a cross near the front, and two pieces either side of the barrel clasp.  Incidentally, once I tried using the barrel clasp method, I was so taken with it I ordered a few hundred of them off of eBay.  I was worried about getting different sizes which would stop me from being able to interchange the bases, so I bought what I hope will be enough to last me.

So there it is ready to be primed, which I forgot to take a photo after, but it is just the same only all black, so you will need to use your imagination.

I will go through my painting next post.

Feel free to leave a comment if you have any questions, or just want to leave a message.


From inspiration, to construction, to completion

I have always had a thing for spaceship miniatures, and even more so when it comes to any Narn ship from Babylon 5.  I have been slowly painting up my collection and adding pieces when I can get them off of ebay.  I regularly look for inspiration for my painting from images taken from the show to other blogs and websites, however a recent perusal ended with me being enthralled by a CG image I saw on DeviantArt, as seen below.

It is two Var’Nic cruisers connected by a generic bridge section.  As soon as I saw it I knew I needed to create it.  I just so happened to have a Var’Nic and a Thentus cruiser that I had yet to paint.  Seeing as these miniatures are no longer in production I decided to make resin copies of them to work with.  Below are the three ships, getting ready to go under the knife.  As you can see they are not the best casts, but I am still learning.

Next you can see it all put together, ready for priming.

And jumping ahead a whole tonne of work, the finished product.

I really enjoyed building and painting this mini.  I think it is the fastest I have every built, primed, and finished anything.  Usually I seem to have months between each of those steps.

Anyway I just wanted to show off the finished miniature, I will return with a few posts that walk through each stage

First post

I had been thinking about starting a blog to share how I paint my miniatures for quite a while, and today I finally sat down and did it.  What really helped me decide to do it is my current project, I am working on a custom Narn ship from the Babylon 5 universe inspired by this image from DeviantArt  It is two Var’Nic ships and the central part of a Thentus crusier.  I am just working on the second to last layer of highlights, so I should have it posted here real soon.

Some of my other ongoing projects include:

30+ one inch StarWars fighters from Studio Bergstrom

25 or so Oness ships and associated fighters from Brigade Models

just got 12 plastic generic one inch fighters from EM4 miniatures

While there are a large number of boxes on the shelves that I can’t wait to jump into.